Technológ

Permanent URI for this communityhttps://drepo.uniza.sk/handle/hdluniza/549

Vychádza spravidla dvakrát ročne. Publikuje vedecké, výskumné, odborné, teoretické práce, návody, štúdie, recenzie, informácie o spracovaní technických materiálov. Zameriava sa na uverejňovanie príspevkov a prác venujúcich sa otázkam z oblasti trieskových a beztrieskových technológií, fyzikálnych princípov, nekonvenčných technológií, technologickosti konštrukcií nástrojov, ekonomike výrobného procesu, ekologizácii, spracovaniu odpadov. Takisto publikuje práce o strojoch, nástrojoch, prípravkoch a meracej technike pre oblasť mechanických technológií, výsledkoch výskumu vo sfére informačných technológií v technologickej oblasti. Uverejňuje práce o histórii a vývine mechanických technológií. Časopis zverejňuje príspevky v jazykoch: slovenskom, českom, poľskom, ruskom, anglickom a nemeckom.

Browse

Search Results

Now showing 1 - 4 of 4
  • Item
    Kovokeramické trecie materiály využívané v práškovej metalurgi
    (University of Žilina, 2024) Kantoríková, Elena
    Metal-ceramic materials are produced from a mixture of metal and ceramic powders. These are primarily sintered carbides for cutting tools and friction materials for brake linings. Their use is important in cases where it is not possible to use normal friction materials. Important is a high coefficient of friction even at high temperature, good thermal conductivity, strength and resistance to abrasion.
  • Item
    Vplyv Ti na mechanické a fyzikálne vlastnosti AlSi5Cu2MG zliatiny
    (University of Žilina, 2024) Sýkorová, Martina; Bolibruchová, Dana
    The hypoeutectic aluminum alloy AlSi5Cu2Mg is used in the field of high-strength cylinder head castings for the automotive sector due to its favorable combination of mechanical, physical, and foundry properties. The regulation of the chemical composition of the AlSi5Cu2Mg alloy set by the manufacturer limits the use of standard grain refiners based on Al-Ti and Al-Ti-B due to the limited content of Ti (max. 0.03 wt.%). The article is focused on the possibility of increasing the Ti content in this specific alloy above 0.03 wt. % Ti. The article investigates the effect of graded addition of Ti (0.1; 0.2 and 0.3 wt. % Ti) on the resulting mechanical and physical properties of the AlSi5Cu2Mg alloy. In this paper, the effect of T6 heat treatment on the resulting mechanical and physical properties was also evaluated. The physical properties of the experimental alloys with Ti addition decreased with increasing Ti content. No significant changes in the mechanical properties were observed due to the addition of Ti. The ductility of the experimental alloys increased positively. The best combination of mechanical and physical properties was demonstrated by AlSi5Cu2Mg alloy with the addition of 0.1 wt. % Ti.
  • Thumbnail Image
    Item
    Materiály s vysokou teplotou tavenia využívané v práškovej metalurgii
    (University of Žilina, 2024) Kantoríková, Elena
    Metals with a high melting point are frequently used materials in technical practice. Their fundamental advantage over other metal materials is their higher melting temperature, which exceeds the melting temperature of iron. Thanks to this physical property, such metals and their alloys can be used in environments where the components are subject to high thermal stress.
  • Thumbnail Image
    Item
    Porovnanie charakteristík tvárniteľnosti vysokopevných dvojfázových ocelí skúškou ťahom a LDH skúškou
    (University of Žilina, 2023) Tomáš, Miroslav; Kulya, Juliy Martyn; Kokarda, Vladimír; Evin, Emil
    The paper deals with the issue of formability evaluation of high-strength dual phase steels DP800 and DP1000 with a thickness of 1.6 mm. These steels are used for automotive body deformation zones. The material formability was evaluated by tensile testing with evaluation of mechanical properties, normal anisotropy ratio and strain hardening exponent. The process formability of steels was evaluated by LDH test, which is used for different deformation states modelled by the specimen width. The results of the LDH parameter achieved were correlated with the measured material formability parameters.
© 2021 Strojnicka fakulta. Všetky práva vyhradené.